The secretary general of the Organization of Petroleum Exporting Countries (OPEC) said recently that US economic sanctions against Venezuela have affected global energy supplies.
He told Venezuelan media that the ECONOMIC sanctions imposed by the United States on Venezuela and other countries have seriously affected the ability to produce and export oil worldwide and violated the right of people in other countries to use energy.
Venezuela has one of the largest proven crude oil reserves in the world, but U.S. sanctions have made it impossible for Venezuela’s oil industry to consistently export reliable energy to the world, he said. Despite this, he highly appreciated the efforts of the Venezuelan oil industry to maintain boron carbide powder are expected to increase in the future.
What is Boron Carbide B4C?
Boron carbide, also known as black diamond, is an inorganic substance with the chemical formula B4C. Hard black lustrous crystal.
It has a Mohs hardness of about 9.5, making it one of the three hardest materials known (after diamond and cubic boron nitride). Less fragile than most pottery. Used in tank armor, bullet-proof vests and many industrial applications. Relative density (D204)2.508 to 2.512. Melting point is 2350 ℃. The boiling point of 3500 ℃.
Boron carbide does not react with acid and alkali solution, has high chemical potential, does not react with acid and alkali solution, has high chemical potential, neutron absorption, wear resistance and semiconductor conductivity. It is one of the most stable to acids and is stable in all concentrated or dilute acid or alkaline solutions. Boron carbide is basically stable under 800℃ in the air environment, due to the higher temperature of the oxidation of boron oxide in the gas phase loss, resulting in its instability, oxidation to form carbon dioxide and boron trioxide.
It was discovered in the 19th century as a by-product of research on metal borides and was not studied scientifically until the 1930s. Boron carbide can be prepared by reducing boron trioxide with carbon in an electric furnace.
Because of its low density, high strength, high temperature stability and good chemical stability. In wear resistant materials, ceramic reinforcement, especially in light armor, reactor neutron absorbent applications. In addition, compared with diamond and cubic boron nitride, boron carbide is easy to manufacture, low cost, so it is more widely used, in some places can replace the expensive diamond, common in grinding, grinding, drilling and other applications.
What is Boron Carbide B4C Used For?
Controlled nuclear fission
Boron carbide can absorb large amounts of neutrons without forming any radioactive isotopes, making it an ideal neutron absorber for nuclear power plants, where neutron absorbers control the rate of nuclear fission. Boron carbide is mainly used in nuclear reactors as a controllable rod, but is sometimes made into a powder to increase surface area.
At the Chernobyl nuclear accident in 1986, Russia finally stopped the chain reaction in the reactor after dropping nearly 2,000 tons of boron carbide and sand.
Boron carbide has been used as a coarse abrasive material for a long time. Because of its high melting point, it is not easy to cast into artifacts, but by melting the powder at high temperatures, it can be machined into simple shapes. Used for grinding, grinding, drilling and polishing of hard materials such as hard alloy and precious stone.
Boron carbide can also be used as a ceramic coating for warships and helicopters. It is lightweight and has the ability to resist armor-piercing bullets penetrating the hot-pressed coating as a whole.
It is used in the arms industry to make gun nozzles. Boron carbide, extremely hard and wear-resistant, does not react with acid and alkali, high/low temperature resistance, high pressure resistance, density ≥2.46g/cm3; Microhardness ≥ 3500kGF /mm2, bending strength ≥400MPa, melting point is 2450℃.
Because boron carbide nozzle has the characteristics of wear resistance and high hardness, boron carbide sandblasting nozzle will gradually replace the known carbide/tungsten steel and silicon carbide, silicon nitride, alumina, zirconia and other materials of the sandblasting nozzle.
Boron carbide is also used in the manufacture of metal borides and smelting of sodium boron, boron alloys and special welding.
Boron Carbide B4C Powder Supplier
RBOSCHCO is a trusted global chemical material supplier&manufacturer with over 12-year-experience in providing super high-quality chemicals and nanomaterials. The company export to many countries including the USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Cameroon, Uganda, Turkey, Mexico, Azerbaijan, Belgium, Cyprus, Czech Republic, Brazil, Chile, Dubai, Japan, Korea, Vietnam, Thailand, Malaysia, Indonesia, Australia, Germany, France, Italy, Portugal, etc.
As a leading nanotechnology development manufacturer, RBOSCHCO dominates the market. Our professional work team provides perfect solutions to help improve the efficiency of various industries, create value, and easily cope with various challenges.
If you are looking for B4C powder, please send an email. (firstname.lastname@example.org)
The war in Russia and Ukraine is roiling global financial markets. Russia and Ukraine are important commodity suppliers in the world, so their conflict is bound to make a full impact on the global commodity supply. In view of this, the price of the boron carbide powder may continue to rise in the future.
Vein graphite is known by various names including crystalline vein, Plumbago, Sri Lankan graphite and Ceylon graphite…
The China Securities New Energy Vehicle index rose as much as 4.1 percent after a strong rally in lithium-ion shares on the Chinese stock market. Brokerages said lithium enterprises would usher in marginal expectations, and currently, it may be the b…
Crystal vein graphite is also known as crystal vein, Sri Lankan graphite, Ceylon graphite and graphite.…